Marwel 5.01 PU

Ten crimpy pinches. Holds are suitable to vertical climbing walls for hard routes and boulders. Fastened with capheaded bolts M10 and screws. Bolts are not included. Holds are roughened on surface. Marwel range. Holoubek – Holow back Suitable for advanced climbers. 10501 – 10 Marwel, 5 – L, 01 – Number Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be…

Read More

MARWEL 7.01 PU

Three crimpy pinches. Holds are suitable to vertical climbing walls. Fastened with capheaded bolts M10 and screws. Bolt is not included. Holds are roughened on surface. Marwel range. Holoubek – Holow back Suitable for advanced climbers. 10701 – 10 Marwel, 7 – XXL, 01 – Number Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be…

Read More

Fins 4.01 PU

Ten crimps. Holds are suitable for vertical climbing and hard climbing in overhangs. Fastened with screws. Bolts are not included. Suitable for advanced climbers. 14401 – 14 Fins, 4 – M, 01 – Number Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be used wire brush during cleaning due to…

Read More

JIBS 6 RINX PU

Ten crimpy screw-on holds in RinX design from polyurethane. They are for fixing on flat plywood. Screws are not included in set. Design rings on surface. Steel washers inside Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be used wire brush during cleaning due to…

Read More

Jibs 7 PU

Ten screw on crimps. Holds are suitable to use around edges of climbing walls and volumes. The holds extend beyond the edge, creating a positive grip. Fastened with screws. Bolts are not included. Suitable for advanced climbers. Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be used wire brush during…

Read More

XS 5 PU

Ten small, positive crimps suitable for strong fingers. Old climbing holds again in production. Fastened with capheaded or countersunk bolts M10 (dual system). Bolts are not included. Great climbing holds for bouldering. XS K1 – old name of this set of holds. Properties of polyurethane holds are more softness and flexibility. Due to these properties…

Read More

XS 6 PU

Ten small crimps, maybe little sharp, suitable for strong fingers. Old climbing holds again in production. Fastened with capheaded or countersunk bolts M10 (dual system). Bolts are not included. Great climbing holds for bouldering. XS K2 – old name of this set of holds. Properties of polyurethane holds are more softness and flexibility. Due to…

Read More

XS 7 PU

Ten small crimps, suitable for system boards and bouldering. Holds are axially symmetric. Old climbing holds again in production. Fastened with capheaded or countersunk bolts M10 (dual system). Bolts are not included. Great climbing holds for bouldering. Suitable for system board. XS K3 – old name of this set of holds. Properties of polyurethane holds…

Read More

CRUX 8 TANX PU

Twelve flatted positive holds, mostly round shapes suitable for use in roofs overhangs. Fastened with capheaded or countersunk bolts M10 (dual system). Bolts are not included. Great climbing holds for bouldering. Suitable for use in big overhangs. Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not…

Read More

CRUX 10 PU

Dvacet lištových chytů. Perfektní pro použití ve velkých převisech. Připevňují se pomocí šroubů M10 s válcovou nebo zápustnou hlavou (dual system) a nebo pouze pomocí vrutů. Šrouby nejsou součástí balení. Perfektní lezecké chyty pro bouldering a hlavně do vytrvalostních cest. Velmi vhodné pro montáž do převisů. Vlastností všech polyuretanových chytů je větší měkkost a pružnost takže…

Read More

RINX SMALL PU

Twenty crimp holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Great for bouldering Design rings on surface. Weight [g]: 2580 Max. surface slope: 0° Grip: small crimp Number of holds: 20 pcs/set No.: #1153, #1154, #1155, #1156, #1157, #1158, #1159, #1160, #1161, #1162 #1163,…

Read More

RINX MEDIUM PU

Ten crimp holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Great for bouldering and endurance routes. Design rings on surface. Weight [g]: 2860 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set No.: #1173, #1174, #1175, #1176, #1177, #1178, #1179, #1180,…

Read More

RINX LARGE PU

Five big holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Design rings on surface. Properties of polyurethane holds are more softness and flexibility. Due to these properties of polyurethane materials should not be used wire brush during cleaning due to surface smoothing holds! Weight…

Read More

CRATER 1 PU

One big crimpy ring hold. In Crater 1 there is one part which is bigger then rest of hold. You can use this hold also in overhangs. Fastened with capheaded or countersunk bolts M10 (dual system) or with three screews . Bolts are not included. Possibility of mounting screws only. Diameter 40cm Attractive design. Easily…

Read More

CRATER 2 PU

One big ring hold. Crater 2 is slopy more then crimpy inside. Fastened with capheaded or countersunk bolts M10 (dual system) or with three screews . Bolts are not included. Possibility of mounting screws only. Diameter 40cm Attractive design. Easily recognizable on the climbing wall. Great for bouldering. Low weight – polyuretan. Weight [g]: 1700…

Read More

CRATER 3 PU

One big ring hold. Crater 3 is most positive from three craters. You can use this hold also in overhangs. Fastened with capheaded or countersunk bolts M10 (dual system) or with three screews. Bolts are not included. Possibility of mounting screws only. Diameter 40cm Attractive design. Easily recognizable on the climbing wall. Great for bouldering.…

Read More

SLATE TETRIS PU

One big crimpy and slopy hold. On Tetris there is many parts for grab. Fastened with capheaded bolts M10, or with three screews . Bolts are not included. Possibility of mounting screws only. Attractive Slate design. Easily recognizable on the climbing wall. Great for bouldering. Low weight – polyuretan. Holoubek – Holow back Properties of…

Read More

ELEMENT 1 TURTLE

One big hold “turtle” usable as crimp and sloper. Fastened using the self drilling screws. Bolts are not included. Attractive design Weight [g]: 2528 Max. surface slope: 30° Grip: small crimp Number of holds: 1 pcs No.: #797 Montage: 5pcs screws M 5.0 x 60 mm. Tightening torque acting on the screw fastening is recommended…

Read More

JIBS 2

Ten screw-on crimpy holds in various shapes. Useful for intermediate climbers! They are for fixing on flat plywood. Screws are not included in set. Weight [g]: 1082 Max. surface slope: 0° Grip: small crimp Number of holds: 10 pcs/set Montage: 34pcs of screws M 5.0 x 35 mm. Tightening torque acting on the screw fastening…

Read More

JIBS 4

Ten screw-on positive holds in “fontainebleau” shapes. Useful for intermediate climbers! They are for fixing on flat plywood. Screws are not included in set. Weight [g]: 1006 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 27pcs of screws M 5.0 x 35 mm. Tightening torque acting on the screw fastening…

Read More

JIBS 5

Ten screw-on positive holds in various shapes. Useful for intermediate climbers! They are for fixing on flat plywood. Screws are not included in set. Weight [g]: 990 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 20pcs of screws M 5.0 x 35 mm. Tightening torque acting on the screw fastening…

Read More

XS 2

Ten small holds of positive shapes. Fastened with capheaded bolts M10. Holds are also suitable for use on children’s walls. Bolts are not included. Weight [g]: 1201 Max. surface slope: 30° Grip: edge Number of holds: 10 pcs/set No.: #211, #212, #213, #214, #215, #216, #217, #218, #219, #220 Montage: 10pcs capheaded bolts M10 x…

Read More

XS 3

Ten small holds of positive shapes. Fastened with capheaded bolts M10. Holds are also suitable for use on children’s walls. Bolts are not included. Weight [g]: 839 Max. surface slope: 30° Grip: edge Number of holds: 10 set/set Montage: 10pcs capheaded bolts M10 x 40 mm Tightening torque acting on the bolt fastening is recommended…

Read More

XS 4

Ten small holds of crimpy shapes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 946 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts M10 x 40 mm Tightening torque acting on the bolt fastening is recommended for maximum 25Nm. Size: 10 x XS Material:…

Read More

S3

Ten holds of crimpy shapes. Fastened with capheaded bolts M10. Useful for intermediate climbers. Bolts are not included. Weight [g]: 1662 Max. surface slope: 0° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts M10 x 40 mm + 10pcs screws M 5.0 x 40 mm. Tightening torque acting on the bolt fastening…

Read More

S4

Ten holds of positive shapes. Fastened with capheaded bolts M10. Holds are suitable for use on playgrounds or children walls. Bolts are not included. Weight [g]: 1491 Max. surface slope: 45° Grip: edge Number of holds: 10 pcs/set No.: #271, #272, #273, #274, #275, #276, #277, #278, #279, #280 Montage: 10pcs capheaded bolts M10 x…

Read More

S6

Ten positive holds. Washer is made of dual-system, thus holds are fastened with screws M10 cylindrical or conical head. Bolts are not included. Weight [g]: 3900 Max. surface slope: 60° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 6pcs M10 x 40 mm, 4pcs M10 x 50 mm. Tightening torque acting…

Read More

S 7 DROPS

You will try to use thumb during climbing on this ten crimp holds. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Climbing holds great for bouldering and hard endurance routes. Attractive design. Weight [g]: 2750 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set No.:…

Read More

S 8 CORC

Ten crimps holds. On these climbing holds you will try push your fingers deeper inside. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Climbing holds great for bouldering and hard endurance routes. Picot edge design. Weight [g]: 2344 Max. surface slope: 30° Grip: small crimp Number of holds:…

Read More

NATURE 2

Ten positive holds different sizes, shape reminiscent holds of french limestone areas. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 3505 Max. surface slope: 90° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts 6x M10 x 40 mm, 2x M10 x 50 mm, 1x M10 x 60 mm, 1x…

Read More

NATURE 3

Ten holds of different sizes, shapes and roughened surface like holds in granite areas. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 2262 Max. surface slope: 30° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 8x M10 x 40 mm, 2x M10 x 50 mm. Tightening torque acting…

Read More

NATURE 5

Ten holds of different sizes. The shape is suitable for difficult climbing in the more overhang profile. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 5688 Max. surface slope: 60° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded – 5x M10 x 50 mm, 5x M10 x 60 mm, +…

Read More

NATURE 6 Slate

Ten “rock” holds different sizes, shape like the rock. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 4821 Max. surface slope: 45° Grip: small crimp Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 6x M10 x 40 mm, 2x M10 x 50 mm, 2x M10 x 60 mm, + 10pcs…

Read More

NATURE 8 Slate

Ten holds in the rock design, suitable for advanced climbers. Washer is made of dual-system, thus holds are fastened with screws M10 cylindrical or conical head. Bolts are not included. Weight [g]: 3900 Max. surface slope: 45° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 6pcs M10 x 40 mm, 4pcs…

Read More

COSMIX 1

Ten holds of various sizes, shape allowing several modes of grip. Bolts are not included. Weight [g]: 2129 Max. surface slope: 30° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 9x M10 x 40 mm, 1x M10 x 50 mm + 4pcs screws M 5.0 x 40 mm. Tightening torque acting…

Read More

COSMIX 2

Ten crimpy holds of various sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 4010 Max. surface slope: 30° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 8x M10 x 40 mm, 1x M10 x 50 mm, 1x M10 x 60 mm + 8pcs screws M 5.0 x…

Read More

COSMIX 3

Ten holds “piggy or stumps” of various sizes, shape allowing several ways of grip. Bolts are not included. Weight [g]: 4450 Max. surface slope: 60° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 7x M10 x 40 mm, 2x M10 x 50 mm, 1x M10 x 60 mm + 9pcs screws…

Read More

COSMIX 5

Ten holds in the rock design, suitable for advanced climbers. Washer is made of dual-system, thus holds are fastened with screws M10 cylindrical or conical head. Bolts are not included. Weight [g]: 3900 Max. surface slope: 45° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 6pcs M10 x 40 mm, 4pcs…

Read More

COSMIX 6

Seven holds in bubbles design various shapes. Fastened with capheaded or countersunk bolts M10 (dual system). Bolts are not included. Attractive design Easily recognizable on the climbing wall Weight [g]: 3750 Max. surface slope: 30° Grip: edge Number of holds: 7 pcs/set No.: #1021, #1022, #1023, #1024, #1025, #1026, #1027, Montage: 7pcs capheaded bolts -3pcs…

Read More

CRUX 1

Ten crimpy holds. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 1242 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 10x M10 x 40 mm + 5pcs screws M 5.0 x 40 mm. Tightening torque acting on the bolt fastening is recommended for…

Read More

CRUX 3

Ten good-crimpy holds. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 3550 Max. surface slope: 45° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 6x M10 x 40 mm, 3x M10 x 50 mm,1 x M10 x 60 mm + 10pcs screws M 5.0 x 40 mm. Tightening…

Read More

CRUX 4

Ten crimpy-holds (duck beaks) of similar sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 2148 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 10x M10 x 40 mm, + 10pcs screws M 5.0 x 40 mm. Tightening torque acting on the bolt…

Read More

CRUX 5 RinX

Ten crimpy-holds with design circles, different sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 5735 Max. surface slope: 30° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 10x M10 x 40 mm + 10pcs screws M 5.0 x 40 mm. Tightening torque acting on the bolt fastening…

Read More

CRUX 6

Ten crimpy-holds of different sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 4788 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts – 9x M10 x 40 mm, 1x M10 x 50 mm + 10pcs screws M 5.0 x 40 mm. Tightening torque acting…

Read More

CRUX 7

Ten crimpy holds of various sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 4038 Max. surface slope: 45° Grip: edge Number of holds: 10 pcs/set Montage: 10pcs capheaded bolts 9x M10 x 40 mm, 1x M10 x 50 mm + 10pcs screws M 5.0 x 40 mm. Tightening torque acting on…

Read More

CRUX 9 CORC

Eight bigger crimps holds. On these climbing holds you will try push your fingers deeper inside. Some of these holds are suitable to mount with wood screws near edge of climbing walls. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Picot edge design. Suitable to mount with wood…

Read More

HIFIVE 1

Five positive holds various sizes. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 3950 Max. surface slope: 45° Grip: edge Number of holds: 5 pcs/set Montage: 5pcs capheaded bolts – 2x M10 x 40 mm, 2x M10 x 60 mm, 1xM10 x 70 mm. Size: 2xXL, 2xXXL, 1xXXXL Material: Polyester mixture

Read More

HIFIVE 2

Five crimpy-holds. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 3950 Max. surface slope: 30° Grip: small crimp Number of holds: 5 pcs/set Montage: 5pcs capheaded bolts 4x M10 x 50 mm,1x M10 x 60 mm Material: Polyester mixture

Read More

HIFIVE 3

Five crimpy holds “whales” enabling takeover holds with both hands. Fastened with capheaded bolts M10. Bolts are not included. Weight [g]: 5662 Max. surface slope: 45° Grip: edge Number of holds: 5 pcs/set No.: #761, #762, #763, #764, #765, Montage: 5pcs capheaded bolts 2x M10 x 50 mm, 3x M10 x 60 mm + 5pcs…

Read More

HIFIVE 5 SLATE

Five “rock” holds. Slate design. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Great for endurance routes. Weight [g]: 6218 Max. surface slope: 60° Grip: edge Number of holds: 5 pcs/set No.: #1183, #1184, #1185, #1186, #1187 Montage: 5pcs capheaded bolts 1x M10 x 40mm, 2x M10 x…

Read More

RINX SMALL

Twenty crimp holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Great for bouldering Design rings on surface. Weight [g]: 3970 Max. surface slope: 0° Grip: small crimp Number of holds: 20 pcs/set No.: #1153, #1154, #1155, #1156, #1157, #1158, #1159, #1160, #1161, #1162 #1163,…

Read More

RINX MEDIUM

Ten crimp holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Great for bouldering and endurance routes. Design rings on surface. Weight [g]: 4300 Max. surface slope: 30° Grip: small crimp Number of holds: 10 pcs/set No.: #1173, #1174, #1175, #1176, #1177, #1178, #1179, #1180,…

Read More

RINX LARGE

Five big holds with rounded shape. Fastened with capheaded or countersunk bolts M10 (dual system) and screws. Bolts are not included. Design rings on surface. Weight [g]: 7300 Max. surface slope: 30° Grip: edge Number of holds: 5 pcs No.: #1098, #1099, #1100, #1101, #1102 Montage: 5 pcs capheaded bolts 4x M10 x 50mm, 1x…

Read More

BIG 5

One big hold. Fastened with capheaded or countersunk bolt M10 (dual system) and one screw. Bolts are not included. Attractive design Weight [g]: 1493 Max. surface slope: 0° Grip: small crimp Number of holds: 1 pcs No.: #775 Montage: 1pcs capheaded bolt -1 x M10 x 60 mm + 1 pcs screw M 5.0 x…

Read More

BIG 6

One big crimp and sloper hold. Fastened with capheaded or countersunk bolt M10 (dual system) and one screw. Bolts are not included. Weight [g]: 1524 Max. surface slope: 0° Grip: small crimp Number of holds: 1 pcs No.: #776 Montage: 1pcs capheaded bolt -1 x M10 x 70 mm + 1 pcs screw M 5.0…

Read More